Iron Gates · Los Angeles

Handmade iron gates,
built to last generations

Custom iron driveway and pedestrian gates, from ornate estate designs to clean modern lines. Swing, sliding, bi-folding and telescopic, made to fit your entrance and your driveway’s slope. Nothing is made until you approve the blueprint.

Handmade ornate iron double driveway gate in Los Angeles

How each iron gate opens

The right type depends on your driveway: its length, slope and how close it is to the street. Press play to see each one open. We check all of this at your design consultation.

Every gate we build is custom made. These are only a few ideas, and the options are almost endless.

01Opens like a door

Iron swing gates

FRONT VIEWTOP VIEWARM MOTORARM MOTOR▼ STREET

Single or double gates, opened by arm motors mounted on the gate. Needs clear, fairly flat space behind the gate to open.

02When the driveway rises behind the gate

Iron uphill swing gates

FRONT VIEWSIDE VIEW◀ STREETDRIVEWAY RISES ▲

The gate is hung so it lifts as it opens, following the slope up. It clears the driveway instead of hitting it.

03Slides behind the wall

Iron sliding gates

FRONT VIEWTOP VIEWMOTORSLIDES BEHIND THE WALL▼ STREET

Slides open behind a block wall, driven by a slide motor standing right next to the gate. Needs wall space about as wide as the opening.

04Two panels that stack

Iron telescopic sliding gates

FRONT VIEWTOP VIEWMOTORSLIDES BEHIND THE WALL▼ STREET

Not enough wall for a full slide? Two panels stack behind the wall as they open, so they need about half the space.

05Folds in the middle

Iron bi-folding gates

FRONT VIEWTOP VIEW▼ STREET

Each side folds in half as it opens, so it needs about half the swing space. A strong fit close to the street.

06Walk-through and side gates

Iron pedestrian gates

FRONT VIEWTOP VIEW▼ STREET

Match your driveway gate and fence, with keypad and smart lock options.

Built to last

Galvanized against rust, then finished by hand

Every iron gate is hot-dip galvanized to stop rust from the inside out. Handmade estate gates get several layers of spray finish, and modern steel gates are powder coated in your color. Solid frames, clean welds and strong hinges keep your gate straight and quiet for years.

Book Design Consult

How we build your iron gate

Design consultationWe visit your home, measure the entrance and talk through styles and options.
2D blueprintYou approve the exact design before anything is made.
Handmade in ironYour gate is built, galvanized and finished to the approved design.
Installed in 1 to 5 daysWe install, clean up and walk you through it, including automation if you added it.
Reviews

What homeowners say about their gates

Google5.0★★★★★550+ reviews

★★★★★

“We hired DNA for a newly constructed 10,000 sq-ft house. We had very high expectations of the gates’ quality to match the quality of the house designed by a well-known architect in Los Angeles. Every component was built and selected carefully with high quality.”

IIraj NasseriGoogle review
★★★★★

“From start to finish, the team was professional, efficient, and knowledgeable. The quality of the gate and the attention to detail during installation were outstanding. The team kept everything tidy and was respectful of my property throughout the entire process. I now have a gate that not only adds security but also enhances the curb appeal of my home.”

NNate RosenbergGoogle review
★★★★★

“We installed 3 gates from DNA Gates. They were fast and really did a good job installing the gates. Very professional”

JJin ChungGoogle review

See all reviews →

Questions about iron gates

Which iron gate is right for my driveway?

It depends on three things: how much flat space you have behind the gate, how much wall or fence you have beside it, and the slope. Plenty of flat space behind: a swing gate. Wall space beside the opening: a sliding gate. Short driveway close to the street: a bi-folding or telescopic gate. We measure all of this at your design consultation and recommend the best fit.

How much room does a swing gate need?

Each side needs clear space behind it about as wide as the gate itself, so it can swing all the way open. If cars park there or the driveway is short, a sliding or bi-folding gate usually works better.

When do I need a telescopic sliding gate?

A regular sliding gate needs wall or fence space about as wide as the opening, so it can slide fully behind it. If you only have about half that space, a telescopic gate uses two panels that stack as they open, so it fits.

My driveway slopes. Can I still have a swing gate?

Yes. If the driveway rises behind the gate, we build an uphill swing gate that lifts as it opens so it clears the slope. A sliding gate is also a good choice on a slope.

What motor does each gate type use?

Swing gates use arm motors that connect the pillar to the gate, such as the LiftMaster LA500. Sliding and telescopic gates use a standing slide motor behind the wall, such as the LiftMaster RSL12UL. We add remotes, keypads and video intercoms the same way.

Will an iron gate rust?

Not when it is built right. We hot-dip galvanize every iron gate, which coats the steel in zinc to stop rust. Handmade gates then get several layers of spray finish, and modern steel gates are powder coated.

Iron or aluminum: which is right for me?

Iron is heavier and stronger, and it is the best choice for ornate, classic and estate designs like the ones on this page. Aluminum is lighter and suits modern slat and privacy designs.

Invest in an entrance you’ll love coming home to, using the highest-quality materials

Custom-Built to Match Your Home
Fully Licensed, Bonded & Insured
Fast Responses & Clear Communication
Stress-Free Installation & Cleanup
Backed by a 5-Year Warranty

Request Design Consult

Design consultation form

The live form appears in Preview and on the website.